PowerBoss commander t82 europe Скачать руководство пользователя страница 83

Страница: 83 / 96

Commander T Series PB# 4100032

Rev.C 03/12

Page 83

Adjusting The Parking Brake Cable Length

1. Park the machine on a level surface and chock the

wheels.

2. Place the parking brake lever in the OFF position.
3. Turn the knurled handle counter-clockwise to loosen

the tension as far as possible.

4. Locate the cable clevis ends for the parking brake

cables in the left front wheel well.

5.  Disconnect the clevis ends from the bar.
6.  Loosen the jam nuts at the base of the clevis.
7.  Turn the clevis clockwise three or four complete

turns.

8. Tighten the jam nuts and re-install the clevis ends

onto the bar.

9. Adjust the knurled handle on the parking brake

lever.

Cable Adjustment for Standard brake

1. Locate the parking brake cable in the top of the left

wheel well opening.

2.  Loosen the locking nut located against the hex bar.
3.  Thread the cable end into the hex bar.
4.  If threads are not sufficient for adjustment,

disconnect the springs, move the cable bars to the

next adjusting hole on the hex bar and reconnect

the springs.

5. Retighten the locking nut against the hex bar. This

adjusts both sets of brake shoes.

6. Test the brakes. Readjust if necessary.

PREVENTATIVE MAINTENANCE

Содержание commander t82 europe






























































































Результаты поиска

Содержание commander t82 europe

Отзывы:

PowerBoss commander t82 europe, Руководство пользователя, Страница: 83 / 96

Результаты поиска

Содержание commander t82 europe

Отзывы: