Polaris Sportsman 570 EFI Скачать руководство пользователя

Страница: 27 / 148

FEATURES AND CONTROLS

Switches

Engine Stop Switch

Move the stop switch either left or right to
the OFF position to stop the engine
quickly. The engine will not start or run
when the switch is off.

Both the main switch and the engine stop
switch will shut off all electrical power to
the vehicle, including lights.

Main Key Switch

Use the main key switch to start the engine. See page 49 for starting
procedures.

Headlight Switch

Use the headlight switch to turn the lights on and off and to change the
lights from high beam to low beam. The key must be in the ON position
and the engine stop switch must be in the RUN position to operate the
headlights.

OFF

RUN

Содержание Sportsman 570 EFI





















































































































































Результаты поиска

Содержание Sportsman 570 EFI

Отзывы:

Похожие инструкции для Sportsman 570 EFI

Бренды по названию

Популярные бренды

Polaris Sportsman 570 EFI, Руководство пользователя

Результаты поиска

Содержание Sportsman 570 EFI

Отзывы:

Похожие инструкции для Sportsman 570 EFI

Бренды по названию

Популярные бренды