Polaris Sportsman 570 EFI Скачать руководство пользователя

Страница: 86 / 148

MAINTENANCE

Engine Oil

Oil and Filter Change

11. Lubricate the o-ring on the new filter with a film of fresh engine oil.

Check to make sure the o-ring is in good condition.

12. Install the new filter and rotate it clockwise by hand until the filter

gasket contacts the sealing surface, then turn it an additional 1/2
turn.

13. Remove the dipstick.

14. Add two quarts (1.9 l) of recommended oil.

15. Place the transmission in PARK.

16. Lock the parking brake.

17. Start the engine. Allow it to idle for one to two minutes.

18. Stop the engine.

19. Check for leaks.

20. Check the oil level. Add oil as needed to bring the level to the upper

mark on the dipstick.

21. Dispose of used filter and oil properly.

Содержание Sportsman 570 EFI





















































































































































Результаты поиска

Содержание Sportsman 570 EFI

Отзывы:

Похожие инструкции для Sportsman 570 EFI

Бренды по названию

Популярные бренды

Polaris Sportsman 570 EFI, Руководство пользователя

Результаты поиска

Содержание Sportsman 570 EFI

Отзывы:

Похожие инструкции для Sportsman 570 EFI

Бренды по названию

Популярные бренды