Polaris Sportsman 570 EFI Скачать руководство пользователя

Страница: 103 / 148

101

MAINTENANCE

Lights

High Beam Adjustment

The headlight beam can be adjusted slightly upward or downward. Use
the following procedure to make the adjustment.

1. Position the vehicle on a level surface with the headlight

approximately 25 ft. (7.6 m) from a wall. Place the transmission in
PARK.

2. Measure the distance from the floor to the center of the headlight

and make a mark on the wall at the same height.

3. Start the engine. Turn the headlight switch to high beam.

4. Observe the headlight aim on the wall. The most intense part of the

headlight beam should be two inches (5 cm) below the mark on the
wall. Include rider weight on the seat when measuring.

5. The adjustment knob is located on the right side of the headlight

pod. Adjust the beam to the desired position by turning the knob
either clockwise or counter-clockwise.

Low Beam Adjustment

The low beam can be adjusted slightly
upward or downward.

1. Loosen the Phillips screw located

at the rear of the headlamp.

2. Tilt the headlamp upward or

downward.

3. Tighten the screw.

25 ft.

(7.6 m)

2" (5 cm)

Phillips

Screw

Содержание Sportsman 570 EFI





















































































































































Результаты поиска

Содержание Sportsman 570 EFI

Отзывы:

Похожие инструкции для Sportsman 570 EFI

Бренды по названию

Популярные бренды

Polaris Sportsman 570 EFI, Руководство пользователя

Результаты поиска

Содержание Sportsman 570 EFI

Отзывы:

Похожие инструкции для Sportsman 570 EFI

Бренды по названию

Популярные бренды