Polaris Sportsman 570 EFI Скачать руководство пользователя | Manualshive

Страница: 63 / 148

background image

61

OPERATION

Hauling Cargo

Never exceed the weight capacities
specified for your ATV on warning
labels and in the specifications
section of this manual.

Cargo weight should be evenly
distributed (1/3 on the front rack and
2/3 on the rear rack) and mounted as
low as possible.

NEVER exceed 50 MPH (80 km/h)
when rear cargo loads are above 75
lbs. (34 kg) and/or front cargo loads
are above 37 lbs. (17 kg).

When operating over rough or hilly terrain, reduce speed and cargo
weight to maintain stable driving conditions.

Do not obstruct the headlight beam with cargo.

Use low forward gear when hauling or towing heavy cargo to extend
belt life.

Towing Loads

Always attach a towed load to the hitch point. Remove the hitch from
the ATV when not towing a trailer. If towing a load, reduce rear rack
cargo weight by the amount of tongue weight.
• The combination of rear rack cargo weight and tongue weight must

not exceed the rear rack capacity.

• The total load (operator, accessories, cargo and weight on hitch) must

not exceed the maximum weight capacity of the vehicle.

NOTICE:

Using an improper hitch or exceeding
the maximum tongue weight capacity
can result in serious damage to the
vehicle and will void your ATV
warranty. Never install a hitch longer
than 4" (10 cm). Never install
automotive accessories on your
POLARIS ATV. Always install
POLARIS-approved (or equivalent)
accessories designed for ATV use.

1/3

2/3

Maximum

4" (10 cm)

«
...
61
62
63
64
65
...
»

Содержание Sportsman 570 EFI





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sportsman 570 EFI

Бренд: KAYO MOTOR Страницы: 90

Бренд: Polaris Страницы: 118

Бренд: Polaris Страницы: 147

Бренд: Mi-T-M Страницы: 12

Бренд: Humbaur Страницы: 230

Бренд: E-Z-GO Страницы: 74

Бренд: Palms Страницы: 19

Бренд: Hammerhead Off-Road Страницы: 75

Бренд: Range Road Страницы: 21

Бренд: Yamaha Страницы: 112

Бренд: Yamaha Страницы: 398

Бренд: Yamaha Страницы: 134

Бренд: Salsco Страницы: 42

Бренд: Yamaha Страницы: 193

UTV Desertcross 1000cc-3

Бренд: ODES Страницы: 230

Бренд: Nucamp Страницы: 57

Бренд: Linhai Страницы: 104

Бренд: Linhai Страницы: 132

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды