Polaris Sportsman 570 EFI Скачать руководство пользователя | Manualshive

Страница: 109 / 148

background image

107

MAINTENANCE

Spark Arrester

Failure to heed the following warnings while servicing the spark arrester could
result in serious injury or death. Never run the engine in an enclosed area.
Remove any combustible materials from the area. Wear eye protection and
leather work gloves. Do not stand behind or in front of the vehicle while purging.
Never go under the vehicle while it's inclined.

The exhaust system can get extremely hot. Do not perform service on the spark
arrester while the system is hot. Allow components to cool sufficiently before
proceeding.

Use the following procedure to periodically purge accumulated carbon
from the exhaust pipe/muffler.

1. Remove the arrester clean-

out plug from the bottom of
the muffler.

2. Place the transmission in

PARK.

3. Start the engine.

4. Quickly squeeze and release

the throttle lever several
times to purge carbon from
the system.

5. If carbon comes out of the exhaust, cover or plug the exhaust outlet.

Wear protective gloves.

6. Lightly tap on the exhaust pipe with a rubber mallet while repeating

step 4.

7. If particles are still suspected to be in the muffler, elevate the rear of

the vehicle one foot (30 cm) higher than the front. Block the wheels.

8. Repeat steps 4 to 6 until no more particles are expelled.

9. Stop the engine. Allow the arrester to cool.

10. Reinstall the arrester plug and remove the exhaust outlet cover or

plug.

WARNING

Exhaust

Outlet

Clean-Out Plug

«
...
107
108
109
110
111
...
»

Содержание Sportsman 570 EFI





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sportsman 570 EFI

Бренд: ODES UTVS Страницы: 141

Бренд: MANCO Страницы: 5

Бренд: E-TON Страницы: 30

BOSS RT FATBOY 1026RT RR

Бренд: Meyer Страницы: 44

Бренд: Knox Страницы: 46

Бренд: Austin Motor Company Страницы: 124

Бренд: Toro Страницы: 32

Бренд: Federal Signal Corporation Страницы: 140

Treker 700-109P

Бренд: Land Pride Страницы: 104

Бренд: KAYO MOTOR Страницы: 80

Бренд: Yamaha Страницы: 397

can-am RENEGADE 1000 2015

Бренд: BRP Страницы: 156

Бренд: Baja Страницы: 57

TRACKER LX6 EFI

Бренд: Textron Specialized Vehicles Страницы: 168

Бренд: Ski-Doo Страницы: 22

Бренд: Ski-Doo Страницы: 75

Бренд: Ski-Doo Страницы: 123

Бренд: Polaris Страницы: 135

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды