Polaris Sportsman 570 EFI Скачать руководство пользователя | Manualshive

Страница: 35 / 148

background image

33

FEATURES AND CONTROLS

All Wheel Drive System

The All Wheel Drive system is
controlled by the 4X4 switch.

4X4 Mode

When the switch is on 4X4, the ATV is
in 4X4, and the 4X4 indicator icon in
the instrument cluster display will be
visible.

When in 4X4, the demand drive unit
will automatically engage any time the
rear wheels lose traction. When the
rear wheels regain traction, the
demand drive unit will automatically
disengage.

There is no limit to the length of time
the vehicle may remain in 4X4. The vehicle automatically engages 4X4
when operating in reverse if the switch is set to the 4X4 position.

2X4 Mode

When the switch is on 2X4, the ATV is in two-wheel drive at all times.

Engaging 4X4

The 4X4 switch may be turned on or off while the vehicle is moving.
Initially, the vehicle's electronic system will not enable 4X4 until the
engine RPM is below 3100. Once enabled, 4X4 remains enabled until
the 4X4 switch is turned off. If the switch is turned off while the demand
drive unit is moving, it will not disengage until the rear wheels regain
traction.

Engage the 4X4 switch before getting into conditions where front wheel
drive may be needed. If the rear wheels are spinning, release the throttle
before switching to 4X4.

NOTICE:

Switching to 4X4 while the rear wheels are spinning may cause
severe drive shaft and gearcase damage. Always switch to 4X4 while
the rear wheels have traction or are at rest.

2x4

4X4

Switch

«
...
33
34
35
36
37
...
»

Содержание Sportsman 570 EFI





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sportsman 570 EFI

ROXOR HDUV 2023

Бренд: Mahindra Страницы: 119

Бренд: BOMBARDIER Страницы: 129

ErgoSteer SP001V9810010

Бренд: FENDT Страницы: 40

Бренд: ABI Attachments Страницы: 28

Бренд: Yamaha Страницы: 17

Бренд: Yamaha Страницы: 22

Бренд: Yamaha Страницы: 156

BLASTER YFS200P

Бренд: Yamaha Страницы: 156

BLASTER YFS200N

Бренд: Yamaha Страницы: 153

Бренд: Yamaha Страницы: 153

Бренд: Yamaha Страницы: 155

BIG BEAR YFM400S

Бренд: Yamaha Страницы: 171

Бренд: Yamaha Страницы: 191

Бренд: Realtree Страницы: 12

Бренд: gio Страницы: 20

Бренд: PRONAR Страницы: 125

Sportsman 9921309

Бренд: Polaris Страницы: 145

2015 RZR XP 1000 EPS

Бренд: Polaris Страницы: 150

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды