Polaris Sportsman 570 EFI Скачать руководство пользователя

Страница: 26 / 148

FEATURES AND CONTROLS

Switches

Mode/Reverse Override Switch

This vehicle is equipped with a reverse speed limiter system. To gain
additional wheel speed while backing, release the throttle and depress
the override button.

WARNING!

Pressing the override button while the throttle is open can cause

loss of control, which may result in serious injury or death. Always release the
throttle before pressing the override button.

The override switch is also used to toggle through the modes of the rider
information center. See page 34.

Tip:

The override switch will not function as a MODE switch if the transmission
is in reverse.

4X4 Switch

Use the 4X4 switch to engage 4X4 or 2X4. See page 33.

Mode/Reverse

Override Switch

Main Key Switch

Engine

Stop Switch

Headlight

Switch

4X4 Switch

Содержание Sportsman 570 EFI





















































































































































Результаты поиска

Содержание Sportsman 570 EFI

Отзывы:

Похожие инструкции для Sportsman 570 EFI

Бренды по названию

Популярные бренды

Polaris Sportsman 570 EFI, Руководство пользователя

Результаты поиска

Содержание Sportsman 570 EFI

Отзывы:

Похожие инструкции для Sportsman 570 EFI

Бренды по названию

Популярные бренды