Polaris Sportsman 570 EFI Скачать руководство пользователя

Страница: 34 / 148

FEATURES AND CONTROLS

Automatic Transmission Gear Selector

The transmission gear selector is
located on the right side of the
vehicle.
H: High Gear
L: Low Gear
N: Neutral
R: Reverse
P: Park

To shift gears, brake to a
complete stop. When the engine
is idling, move the lever to the
desired gear.

NOTICE:

Shifting gears with the engine speed above idle or while the vehicle is
moving could cause transmission damage.

Whenever the ATV is left unattended, always place the transmission in
PARK and lock the parking brake.

Belt Life

To extend belt life, use low forward gear when pulling a heavy load at
less than seven miles per hour for extended periods and when operating
uphill at a slow speed.

Gear

Selector

Содержание Sportsman 570 EFI





















































































































































Результаты поиска

Содержание Sportsman 570 EFI

Отзывы:

Похожие инструкции для Sportsman 570 EFI

Бренды по названию

Популярные бренды

Polaris Sportsman 570 EFI, Руководство пользователя

Результаты поиска

Содержание Sportsman 570 EFI

Отзывы:

Похожие инструкции для Sportsman 570 EFI

Бренды по названию

Популярные бренды