Polaris Sportsman 570 EFI Скачать руководство пользователя | Manualshive

Страница: 115 / 148

background image

113

MAINTENANCE

Battery

Battery Installation

Using a new battery that has not been fully charged can damage the
battery and result in a shorter life. It can also hinder vehicle
performance. Follow the battery charging instructions on page 115
before installing the battery.

1. Ensure that the battery is fully charged.

2. Place the battery in the battery holder.

3. With conventional batteries, install the battery vent tube (sealed

batteries do not have a vent tube). The vent tube must be free of
obstructions and securely installed. Route the tube away from the
frame and vehicle body to prevent contact with electrolyte.

WARNING!

Battery gases could accumulate in an improperly installed vent tube

and cause an explosion, resulting in serious injury or death. Always ensure that
the vent tube is free of obstructions and is securely installed as recommended.

4. On conventional batteries, coat the terminals with dielectric grease

or petroleum jelly.

5. Connect and tighten the red (positive) cable first.

6. Connect and tighten the black (negative) cable last.

7. Install the battery cover (if equipped).

8. Secure the battery hold-down strap.

9. Verify that cables are properly routed. Cables should be safely

tucked away at the front and rear of the battery.

«
...
113
114
115
116
117
...
»

Содержание Sportsman 570 EFI





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sportsman 570 EFI

1970 SKI-DADDLER

Бренд: AMF Страницы: 74

Can-Am 450 Series

Бренд: BRP Страницы: 196

Camoplast ATV T4S

Бренд: CAMSO Страницы: 16

5000-05-1774-MAN

Бренд: CAMSO Страницы: 17

Vyper 4WD 1100cc

Бренд: gio Страницы: 113

2005 LT-A700XK5

Бренд: Suzuki Страницы: 477

Бренд: Taylor-Dunn Страницы: 130

Бренд: HAUL MASTER Страницы: 2

Бренд: Bad Boy Страницы: 60

2010 California Roadster

Бренд: ACG Страницы: 53

Бренд: Tracker Off-Road Страницы: 68

Бренд: Tracker Страницы: 156

Бренд: TrailMaster Страницы: 30

Бренд: TrailMax Страницы: 65

Бренд: TrailMax Страницы: 72

Carryall 272 2005

Бренд: Club Car Страницы: 48

Бренд: TTI Страницы: 12

Бренд: Evinrude&JOHNSON Страницы: 83

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды