Polaris Sportsman 570 EFI Скачать руководство пользователя | Manualshive

Страница: 51 / 148

background image

49

OPERATION

Starting the Engine

1. Position the vehicle on a level surface outdoors or in a well-

ventilated area.

2. Place the transmission in PARK.

3. Lock the parking brake.

Tip:

The starter interlock will prevent the engine from starting if the transmission
is in gear and the brake is not engaged.

4. Sit on the vehicle and move the engine stop switch to RUN.

5. Do not press the throttle while starting the engine.

6. Turn the ignition key past the ON position to engage the starter.

Activate the starter for a maximum of five seconds, releasing the
key when the engine starts.

7. If the engine does not start, return the key to the OFF position and

wait five seconds before attempting to start again. Activate the
starter for another five seconds if necessary. Repeat this procedure
until the engine starts.

NOTICE:

Operating the vehicle immediately after starting could cause engine
damage. Allow the engine to warm up for several minutes before
operating the vehicle.

Cold Weather Operation

If the ATV is used year-round, check the oil level frequently. A rising oil
level could indicate the accumulation of contaminates such as water or
excess fuel in the bottom of the crankcase. Water in the bottom of the
crankcase can lead to engine damage and must be drained. Water
accumulation increases as outside temperature decreases.

«
...
49
50
51
52
53
...
»

Содержание Sportsman 570 EFI





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sportsman 570 EFI

Бренд: MANCO Страницы: 4

Бренд: E-TON Страницы: 134

Бренд: Polaris Страницы: 309

Lynx 1200 4-TEC 900 ACE 2018

Бренд: BRP Страницы: 164

Бренд: BOMBARDIER Страницы: 328

Utility Vehicle Workshop

Бренд: Bush Hog Страницы: 11

Бренд: Vermeer Страницы: 88

Бренд: Kubota Страницы: 28

150GKA-2 Series

Бренд: Kandi USA Страницы: 16

Бренд: Landoll Страницы: 80

FourTrax Foreman TRX520FE2 2020

Бренд: Honda Страницы: 287

Бренд: Yamaha Страницы: 589

Бренд: SAFARI Страницы: 50

HardCabs CAN-AM COMMANDER 1000 LIMITED

Бренд: DFK Страницы: 79

Бренд: FIORENTINI Страницы: 21

Бренд: TGB Страницы: 86

Cadence 101018 Series

Бренд: Thule Страницы: 44

Бренд: Ezgo Страницы: 158

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды