Polaris Sportsman 570 EFI Скачать руководство пользователя

Страница: 104 / 148

102

MAINTENANCE

Lights

Headlight Housing Replacement

1. Remove the two screws on the lower front corners of the headlight

pod.

2. Lift the pod slightly while depressing the tabs at the rear of the pod.

3. Lift the pod cover and disconnect the speedometer harnesses from

the speedometer.

4. Unplug the headlamp from the wiring harness.

5. Use a small screwdriver to remove the o-rings from the headlight

mounting tabs.

6. Pull the headlight housing up to release it from the locking tabs.

7. Lift the adjusting knob up to remove it from the locking tabs.

8. Carefully pull the assembly up

and out of the pod.

9. Reverse the steps to install the

new housing and reassemble
the pod. The distance from the
headlamp parting line to the
end of the adjustment knob
stop is 5 1/8" (13 cm).

10. Adjust the headlight aim by

turning the adjusting knob.

5 1/8"

(13 cm)

Содержание Sportsman 570 EFI





















































































































































Результаты поиска

Содержание Sportsman 570 EFI

Отзывы:

Похожие инструкции для Sportsman 570 EFI

Бренды по названию

Популярные бренды

Polaris Sportsman 570 EFI, Руководство пользователя

Результаты поиска

Содержание Sportsman 570 EFI

Отзывы:

Похожие инструкции для Sportsman 570 EFI

Бренды по названию

Популярные бренды