Polaris Sportsman 570 EFI Скачать руководство пользователя

Страница: 105 / 148

103

MAINTENANCE

Lights

Lower Headlamp Replacement

1. Turn the back of the headlight

harness counter-clockwise and
pull the harness assembly away
from the headlight assembly.

2. Remove the headlamp and

install the new headlamp.

3. Reinstall the harness assembly

into the headlight assembly.

4. Turn the headlight harness

clockwise to secure the
headlamp.

Taillight/Brakelight Lamp Replacement

1. Remove the harness connector

from the back of the light
assembly.

2. Turn the lamp counter-clockwise

to remove it.

3. Apply dielectric grease to the

socket and install the new lamp.

4. Reinstall the harness connector.

5. Test the light for proper

operation.

Harness

Lamp

Phillips

Screw

Lamp

Harness

Connector

Taillight

Socket

Содержание Sportsman 570 EFI





















































































































































Результаты поиска

Содержание Sportsman 570 EFI

Отзывы:

Похожие инструкции для Sportsman 570 EFI

Бренды по названию

Популярные бренды

Polaris Sportsman 570 EFI, Руководство пользователя

Результаты поиска

Содержание Sportsman 570 EFI

Отзывы:

Похожие инструкции для Sportsman 570 EFI

Бренды по названию

Популярные бренды