Polaris Sportsman 570 EFI Скачать руководство пользователя | Manualshive

Страница: 111 / 148

background image

109

MAINTENANCE

PVT System

The basic operation of the POLARIS PVT system is dependent on
engine speed and vehicle torque requirements. As engine speed
increases, the force exerted on the movable drive sheave by the
flyweights also increases. This, in turn, increases the amount of pinch
applied to the drive belt. Similarly, if the engine speed decreases, the
amount of centrifugal force decreases, reducing the amount of belt
pinch.

On POLARIS ATVs, the approximate gear ratio difference between
high and low range is 1:2.25. This difference in gearing affects the
operation of the PVT, especially at speeds less than 7 MPH (11 km/h),
due to the system's dependence on engine speed.

For example, when operating at a ground speed of 3 MPH (5 km/h) in
low range, the engine speed would be around 3000 RPM. This is well
above the engagement speed of 1200 - 1400 RPM. However, in high
range at 3 MPH (5 km/h), the engine would be running at only 1500
RPM. Whenever operating this close to the engagement speed, the
engine may be running at a speed too low to provide the pinch needed to
prevent belt slip. Belt slip is responsible for creating the excessive heat
that destroys belts, wears clutch components and causes outer clutch
covers to fail.

The air temperature in the clutch cover is substantially reduced by using
low range while operating at low ground speeds. Reducing the
temperature inside the clutch cover greatly extends the life of the PVT
components (belt, cover, etc.).

«
...
109
110
111
112
113
...
»

Содержание Sportsman 570 EFI





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sportsman 570 EFI

Бренд: KAYO MOTOR Страницы: 213

Бренд: Landa Страницы: 101

Бренд: Ezgo Страницы: 64

Бренд: Snapper Страницы: 82

Бренд: Joyner Страницы: 40

Бренд: Can-Am Страницы: 152

Бренд: Jerr-Dan Страницы: 104

2009 Ranger RZR 800 EFI

Бренд: Polaris Страницы: 332

Бренд: SSR Motorsports Страницы: 55

Бренд: Daimler Страницы: 90

Бренд: Valor Страницы: 41

Бренд: MANCO Страницы: 30

Бренд: E-TON Страницы: 225

Бренд: Yamaha Страницы: 132

Бренд: NINCO Страницы: 2

Cushman HAULER 800X ELiTE 2019

Бренд: Textron Specialized Vehicles Страницы: 66

Бренд: TrailMaster Страницы: 25

Бренд: PENTORA Страницы: 128

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды