PLAYSTAR VARSITY BRONZE Скачать руководство пользователя страница 18

Страница: 18 / 72

Items for STEP 12:

(3) Step 11 Assemblies
(2) Right-hand Sturdy-frame Brackets
(1) Left-hand Sturdy-frame Bracket
(6) #8 x 1

¹₄

" deck screws

(6)

³₈

" x 3

¹₂

" hex bolts

(12)

³₈

" washers

(6)

³₈

" lock nuts

Left-hand

Right-hand

Rear View of bracket and post

assembly showing correct position.

Left-hand

shown

Stops

Attach two right-hand (R) and one left-hand (L)
sturdy-frame brackets onto separate swing post
assemblies (brackets are stamped R and L).

Lay bracket on the flush end of post as shown. Slide
bracket over and down until it stops against the top
and side of the post as shown. When correctly
positioned, the edge of the sturdy-frame bracket will
be parallel with the side of the post.

Use the bracket as a drill guide and drill two

¹₈

" holes

1" deep into the posts. Attach with two #8 x 1

¹₄

" deck

screws.

Again use the bracket as a drill guide and drill two

³₈

" holes through the post. Secure bracket with two

³₈

" x 3

¹₂

" hex bolts,

³₈

" washers and

³₈

" lock nuts.

Repeat for each post.

flush

Caution: Make sure bolts are tight and the

threads of each bolt are at least flush
to the end of the nut to ensure proper
engagement.

Содержание VARSITY BRONZE









































































Результаты поиска

Содержание VARSITY BRONZE

Отзывы:

Похожие инструкции для VARSITY BRONZE

Бренды по названию

Популярные бренды

PLAYSTAR VARSITY BRONZE, Инструкция по безопасности и сборке

Результаты поиска

Содержание VARSITY BRONZE

Отзывы:

Похожие инструкции для VARSITY BRONZE

Бренды по названию

Популярные бренды