PLAYSTAR VARSITY BRONZE Скачать руководство пользователя страница 31

Страница: 31 / 72

Items for STEP 26:

(1) 2" x 4" x 31

¹⁄₂

" board

(1) 2" x 4" x 38

³⁄₄

" board

(2) corner brackets
(8) #8 x 2

¹₂

" deck screws

(8) #8 x 1

¹₄

" deck screws

(1)

³₈

" x 3

¹₂

" hex bolt

(3)

³₈

" x 2" hex bolts

(8)

³₈

" washers

(4)

³₈

" lock nuts

Position 2" x 4" x 31

¹⁄₂

" board approximately 28" up from bottom of tower

flush with the tower and swing beam posts as shown. Attach with #8 x 2

¹₂

deck screws.

Position 2" x 4" x 38

³⁄₄

" board approximately 14" up from bottom of tower

flush with the tower and swing beam post as shown. Attach with #8 x 2

¹₂

deck screws.

Attach corner brackets.

Position brackets so that the short sides are

against the 2" x 4" x 31

¹⁄₂

" board. (See Page 9 for details.)

Use the bracket as a drill guide and drill

¹₈

" holes 1" deep into the board.

Attach with #8 x 1

¹₄

" deck screws.

Again use the bracket as a drill guide and drill

³₈

" holes completely through

the boards. Secure with

³₈

" hex bolts,

³₈

" washers and

³₈

" lock nuts.

NOTE:

If you are bolting
through one
board use a

³₈

" x 2" hex bolt.

If you are bolting
through two
boards, use a

³₈

" x 3

¹₂

" hex bolt.

Back View

AGES

7 & 8 F

OLE

ATTERNS

¹⁄₂

³⁄₄

2" x

4" x

¹⁄₂

2" x

4" x

³⁄₄

28"

14"

Flush

Содержание VARSITY BRONZE









































































Результаты поиска

Содержание VARSITY BRONZE

Отзывы:

Похожие инструкции для VARSITY BRONZE

Бренды по названию

Популярные бренды

PLAYSTAR VARSITY BRONZE, Инструкция по безопасности и сборке

Результаты поиска

Содержание VARSITY BRONZE

Отзывы:

Похожие инструкции для VARSITY BRONZE

Бренды по названию

Популярные бренды