PLAYSTAR VARSITY BRONZE Скачать руководство пользователя страница 24

Страница: 24 / 72

Items for STEP 19:

(5)

³₈

" x 3

¹₂

" hex bolts

(10)

³₈

" washers

(5)

³₈

" lock nuts

Caution: Make sure bolts are tight

and the threads of each
bolt are at least flush to
the nut to ensure proper
engagement.

Leave

Open

Note: If you do not have saw horses, rest beam

on ground and rotate A-frame and single
post simultaneously to the other side
(requires two adults). Single post
must be supported to keep the
bracket from bending.
Complete and rotate back
to original position.

Lift swing beam assembly and
support with saw horses.

From the bottom side of beam, use
the six

³₈

" holes in bottom board as

a drill guide and drill

³₈

" holes back

through both boards.

On the A-Frame end attach three

³₈

" x 3

¹₂

" hex bolts,

³₈

" washers

and

³₈

" lock nuts.

On the single post end only, attach
two

³₈

" x 3

¹₂

" hex bolts,

³₈

" washers

and

³₈

" lock nuts. Leave hole closest

to end open as it will be used to
attach beam to tower assembly

Содержание VARSITY BRONZE









































































Результаты поиска

Содержание VARSITY BRONZE

Отзывы:

Похожие инструкции для VARSITY BRONZE

Бренды по названию

Популярные бренды

PLAYSTAR VARSITY BRONZE, Инструкция по безопасности и сборке

Результаты поиска

Содержание VARSITY BRONZE

Отзывы:

Похожие инструкции для VARSITY BRONZE

Бренды по названию

Популярные бренды