PLAYSTAR VARSITY BRONZE Скачать руководство пользователя страница 16

Страница: 16 / 72

Items for STEP 10:

(2) 2" x 4" x 24

¹⁄₄

" boards

(1) 2" x 4" x 31

¹⁄₂

" boards

(12) #8 x 2

¹⁄₂

" deck screws

Attach two 2" x 4" x 24

¹⁄₄

" boards centered in the tower as shown.

Secure with #8 x 2

¹⁄₂

" deck screws.

Attach one pre-drilled 2" x 4" x 31

¹⁄₂

" boards at dimensions shown.

Make sure there is an overhang of 1

³⁄₄

" on each end of the

2" x 4" x 24

¹⁄₄

" boards as shown. Secure with #8 x 2

¹⁄₂

" deck screws.

AGES

7 & 8 F

OLE

ATTERNS

Items for STEP 9:

(2) 2" x 4" x 31

¹⁄₂

" boards

(8) #8 x 2

¹⁄₂

" deck screws

Attach two pre-drilled 2" x 4" x 31

¹⁄₂

" boards at dimensions shown.

Center boards on tower, there should an overhang on each end of
the boards. Make sure the top and bottom of board is flush while
securing with #8 x 2

¹⁄₂

" deck screws.

AGES

7 & 8 F

OLE

ATTERNS

2" x

4" x

¹⁄₂

2" x

4" x

¹⁄₂

" overhang

¹⁄₈

2" x

4" x

¹⁄₂

¹⁄

₄

¹⁄

₄

¹⁄₈

³⁄₄

overhang

³⁄₈

Содержание VARSITY BRONZE









































































Результаты поиска

Содержание VARSITY BRONZE

Отзывы:

Похожие инструкции для VARSITY BRONZE

Бренды по названию

Популярные бренды

PLAYSTAR VARSITY BRONZE, Инструкция по безопасности и сборке

Результаты поиска

Содержание VARSITY BRONZE

Отзывы:

Похожие инструкции для VARSITY BRONZE

Бренды по названию

Популярные бренды