PLAYSTAR VARSITY BRONZE Скачать руководство пользователя страница 54

Страница: 54 / 72

CLIMBING BAR ASSEMBLY

Items for step 37:

(1) 2" x 4" x 75

³⁄₄

" board (cut previously)

(1) triangle bracket
(2) #8 x 1

¹⁄₄

" deck screws

Attach triangle bracket onto 2" x 4" x 75

³⁄₄

" board.

Lay bracket flat on the board. Slide bracket until
the stops on the underside are tight against the
board and the edge of the bracket is flush with
the corner of the board as shown.

Use the bracket as a drill guide and drill two

¹₈

" holes 1" deep into the board. Attach with

#8 x 1

¹⁄₄

" deck screws.

Again use the bracket as a drill guide and
drill three

³₈

" holes completely through the

board in the locations shown.

Note: When correctly positioned,

this edge of bracket will
be parallel with this
edge of the
board.

flush at corner only

stops

drill

Underside of bracket showing correct positioning

x 4

" x

³⁄₄

x 4

" x

³⁄₄

x 4

" x

³⁄₄

Содержание VARSITY BRONZE









































































Результаты поиска

Содержание VARSITY BRONZE

Отзывы:

Похожие инструкции для VARSITY BRONZE

Бренды по названию

Популярные бренды

PLAYSTAR VARSITY BRONZE, Инструкция по безопасности и сборке

Результаты поиска

Содержание VARSITY BRONZE

Отзывы:

Похожие инструкции для VARSITY BRONZE

Бренды по названию

Популярные бренды