PLAYSTAR VARSITY BRONZE Скачать руководство пользователя страница 12

Страница: 12 / 72

Items for STEP 4:

(8) Corner Brackets

(32) #8 x 1

¹₄

" deck screws

(8)

³₈

" x 3

¹₂

" hex bolts

(6)

³₈

" x 2" hex bolts

(2)

³₈

" x 1

¹₂

" lag screws

(30)

³₈

" washers

(14)

³₈

" lock nuts

➑

Lift tower assembly upright and position
in desired location.

Caution: Ground must be level.

Installation on a hill or incline
will create unsafe conditions.

Position brackets

through

so that the

short sides are against the 2" x 4" x 38

³₄

boards.

Use the bracket as a drill guide and drill

¹₈

" holes 1" deep into the boards. Attach

with #8 x 1

¹₄

" deck screws.

Bracket

through

ONLY

: Use bracket as

a drill guide and drill

³₈

" holes completely through

the boards. Secure with

³₈

" hex bolts (2" through

one board and 3

¹⁄₂

" through two boards),

³₈

" washers and

³₈

" lock nuts.

Special Instructions for Brackets

➐

➑

ONLY

Use bracket as a drill guide and drill one

³₈

" hole

completely through the board on the

long

side and

one

¹₄

hole 1" deep into the board on the

short

side.

Secure the

long

side with a

³₈

" x 3

¹₂

" hex bolt,

³₈

" washers and

³₈

" lock nut. Secure the

short

side

with a

³₈

" x 1

¹₂

" lag screw and

³₈

" washer.

³⁄₄

AGES

9 F

ORNER

RACKETS

Содержание VARSITY BRONZE









































































Результаты поиска

Содержание VARSITY BRONZE

Отзывы:

Похожие инструкции для VARSITY BRONZE

Бренды по названию

Популярные бренды

PLAYSTAR VARSITY BRONZE, Инструкция по безопасности и сборке

Результаты поиска

Содержание VARSITY BRONZE

Отзывы:

Похожие инструкции для VARSITY BRONZE

Бренды по названию

Популярные бренды