PLAYSTAR VARSITY BRONZE Скачать руководство пользователя страница 70

Страница: 70 / 72

CLIMBING WALL – Assembly Instructions

1. Align top of Climbing Wall at right angle 90˚. Lip of

climbing wall should rest on the play deck 1

¹₂

". Using

the Climbing Wall as a template, mark play deck
through the three holes in the climbing wall. Drill three

¹⁄₈

" holes at marked locations.

(Fig. 1)

2. Attach Climbing Wall temporarily to play deck with

three #14 x 1

¹⁄₄

" pan head screws provided.

3. Prepare level area where Climbing Wall touches

ground.

4. Locate and mark the ground on the back side and in

center of Climbing Wall. Remove Climbing Wall and
screw Playset Anchor into the ground (a long
screwdriver will help). Screw the anchor deep enough
so that the center of the loop at the top of the anchor
will be approximately 3

¹₂

" off ground when wall is in

the final position.

5. Reinstall Climbing Wall permanently, attaching it to

play deck using #14 x 1

¹₄

" pan head screws provided.

6. Use the anchor as a drill guide and drill a

³₈

" hole

completely through the Climbing Wall. Attach
Climbing Wall to anchor with one

³₈

" x 1

¹⁄₄

" hex bolt,

two

³₈

" washers and one

³₈

" lock nut provided in the

anchor kit.

(Fig. 2)

Warning: Failure to anchor the Climbing Wall properly

could cause serious injury from children
lifting the Unit.

¹|₂

anchor location

Fig. 1

Fig. 2

Содержание VARSITY BRONZE









































































Результаты поиска

Содержание VARSITY BRONZE

Отзывы:

Похожие инструкции для VARSITY BRONZE

Бренды по названию

Популярные бренды

PLAYSTAR VARSITY BRONZE, Инструкция по безопасности и сборке

Результаты поиска

Содержание VARSITY BRONZE

Отзывы:

Похожие инструкции для VARSITY BRONZE

Бренды по названию

Популярные бренды