PLAYSTAR VARSITY BRONZE Скачать руководство пользователя страница 13

Страница: 13 / 72

AGES

7 & 8 F

OLE

ATTERNS

Items for STEP 5:

(1) 2" x 4" x 46

³⁄₄

" board

(4) #8 x 2

¹₂

" deck screws

Predrill the 2" x 4" x 38

³₄

" boards at

the dimension shown.

Center the 2" x 4" x 46

³⁄₄

" board behind

the holes and flush with the top of the
2" x 4" x 38

³₄

" boards. Secure with

#8 x 2

¹₂

" deck screws.

Attach fifteen pre-drilled and counter-sank
1" x 4" x 35

⁷₈

" boards.

Attach the front and back boards flush
with the 2" x 4" x 38

³₄

" boards and equally

space the remaining boards. Secure all
boards with #8 x 1

¹⁄₂

" deck screws. Do not over

tighten the screws.

Note: Gap between boards must
be less than

¹⁄₄

" or a finger entrapment

could exist.

Items for STEP 6:

(15) 1" x 4" x 35

⁷₈

" boards

(90) #8 x 1

¹⁄₂

" deck screws

Caution: Failure to pre-drill and
counter-sink the boards may
result in split lumber.

AGES

7 & 8 F

OLE

ATTERNS

2" x 4"

x 38

³⁄₄

2" x

4" x

³⁄₄

1" x 4" x 35

⁷⁄₈

" (15)

x 4

" x

³⁄₄

Fro

¹⁄₂

Содержание VARSITY BRONZE









































































Результаты поиска

Содержание VARSITY BRONZE

Отзывы:

Похожие инструкции для VARSITY BRONZE

Бренды по названию

Популярные бренды

PLAYSTAR VARSITY BRONZE, Инструкция по безопасности и сборке

Результаты поиска

Содержание VARSITY BRONZE

Отзывы:

Похожие инструкции для VARSITY BRONZE

Бренды по названию

Популярные бренды