PAT DS 50 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 45

background image

42

TSM DS 50-003/REV.C/031-300-190-003/04-20-07

DS50 TROUBLE SHOOTING MANUAL LEVEL 3

11. ERROR CODE MESSAGES

Error Code

Error

Cause

Remedy

E14

Load input
voltage is lower
than the
minimum limit

Cable leading from the
central unit to the load cell is
defective or has water in it.

Load cell defective

Analog channel on main
board is defective

If the cable or connector is damaged
replace the cable or the load cell.
Refer to the troubleshooting manual.

Follow the instructions in the
troubleshooting manual and use the
test fixture to clearly identify a load cell
defect. If in doubt contact Hirschmann
service support. In the event of a load
cell defect replace the load cell
referring to the troubleshooting manual
and crane service documentation.

WARNING: Support the hoist drum
while replacing the load cell.

Clearly identify a main board defect by
referring to the troubleshooting manual.
If in doubt contact Hirschmann service
support. Replace main board or
central unit and transfer calibration
data. Afterwards, load test the system.

E15

Communication
lost to angle
sensor

Angle sensor defective or
main board defective

Replace main board and transfer
calibration data. Afterwards, load test
the system.

«
...
40
41
42
43
44
...
»

Содержание DS 50














































Отзывы:

Нет отзывов

Похожие инструкции для DS 50

MicroVersaTrip Plus

Бренд: GE Страницы: 20

Бренд: GE Страницы: 252

Бренд: Balanced Body Страницы: 12

Бренд: Eagle Pro Страницы: 6

Бренд: GE Страницы: 10

Бренд: Bacharach Страницы: 48

Бренд: HANYOUNG NUX Страницы: 2

Бренд: IDS Страницы: 2

Бренд: Ocutech Страницы: 4

Бренд: Quantum Страницы: 11

Бренд: Quanser Страницы: 21

Бренд: Gaspardo Страницы: 88

TUV COMFORT LIGHT Series

Бренд: olympia electronics Страницы: 4

Бренд: Life Fitness Страницы: 45

VADA TWIN MOTOR MACERATOR

Бренд: Reece Страницы: 7

Бренд: Jenx Страницы: 34

Бренд: B+S Страницы: 16

Бренд: Bavis Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды