PAT DS 50 Скачать руководство пользователя страница 41

Страница: 41 / 45

TSM DS 50-003/REV.C/031-300-190-003/04-20-07

DS50 TROUBLE SHOOTING MANUAL LEVEL 3

11. ERROR CODE MESSAGES

Error Code Table for all DS50A2 cranes

Error Code

Error

Cause

Remedy

Over load

Cutoff due to over load limit

Reduce load or reduce radius

E05

Length pot
error

The boom length reported from
the length pot is too low:

Clutch between length sensor
pot and gear may be defective

+5V supply to length pot faulty.

Length pot defective

With the boom fully retracted, use the
LCD to adjust the length reading until
this error disappears

Completely replace length pot
assembly and readjust length sensor
pot

Check the +5V supply as described in
the troubleshooting manual. Identify
either a main board defect or length pot
assembly defect.

Replace the length pot. Refer to the
troubleshooting manual for instructions.

E11

Length voltage
is less than
the minimum
limit

The voltage level of the length
pot is too low

Clutch between length sensor
pot and gear may be defective

+5V supply to length pot faulty.

Length pot defective

With the boom fully retracted, adjust
the length pot until this error
disappears, then adjust the length
reading with the internal LCD
adjustment

Completely replace length pot
assembly and readjust length sensor
pot

Check the +5V supply as described in
the troubleshooting manual. Identify
either a main board defect or length pot
assembly defect.

Replace the length pot. Refer to the
troubleshooting manual for instructions.

Содержание DS 50














































Результаты поиска

Содержание DS 50

Отзывы:

Бренды по названию

Популярные бренды

PAT DS 50, Руководство по устранению неисправностей

Результаты поиска

Содержание DS 50

Отзывы:

Бренды по названию

Популярные бренды