Parker Coral Sea, Руководство пользователя

Страница: 29 / 248

Installa
tion
Coral Sea Vertical 6800
Page 4-1
4 INSTALLATION REQUIREMENTS
LAND INSTALLATION NOTE: REFER TO SECTION 4.4
REGARDING FEED WATER INSTRUCTIONS FOR LAND
INSTALLATIONS. REFER TO THE REST OF THIS SECTION
FOR INSTALLATION.
All mounting surfaces must be fl at in order to avoid
warping of brackets and frames. Any damage caused
by attaching the system or its components to an uneven
surface is attributed to improper installation, is the
liability of the installer, and is not covered by the Parker
Hannifi n warranty. Grind fl at or use appropriate shims on
uneven surfaces to ensure that mounting of the system
components does not cause bending or warping.
Refer to the foldout illustrations at the back of this manual.
4.1 COMPONENTS SUPPLIED BY
OWNER:
1 Suction piping of 1 inch inside diameter minimum.
The suction line should include a 1/4 turn quick
shut-off valve with a minimum 1” orifi ce and
terminate with a 1 inch American standard national
pipe thread nipple for connection of the supplied 1
inch female national pipe threaded fl ange fi tting.
The entire suction line, fi tting and valve assembly
must be of non-ferrous material. PVC, CPVC, Naval
bronze or another noncorrosive material is correct.
Any ferrous material will cause rust fouling of the
SRC R.O. Membrane Element. Rust fouling of the
R.O. Membrane Element may not be cleanable and
may render the R.O. Membrane Element permanently
damaged. Fouling of the R.O. Membrane Element by
rust is not covered under warranty.
2. Brine discharge line suffi cient to handle the system
brine discharge along with unpotable product water
discharge, and the media fi lter back fl ush waste
water. The line and fi tting must be minimum 1” size,
with 1” piping up to the Parker Hannifi n System and
terminate with a 1 inch American standard national
pipe thread nipple for connection of the supplied 1
inch female national pipe threaded fl ange fi tting.
Ferrous material should not be used as the brine
discharge water is high in salt content and very
corrosive. There should be no valving in this line.
Damage to the system caused by a blocked brine
discharge line will not be covered by warranty.
3. Product water storage tank connection: This fi tting
must be minimum 1” size, with 1” piping up to the
Parker Hannifi n System and terminate with a 1 inch
American standard national pipe thread nipple for
connection of the supplied 1 inch female national
pipe threaded fl ange fi tting.
Ferrous material should not be used as the product
water is very aggressive and slightly acidic. Product
water will turn red or brown if ferrous material is
used in the product water distribution line or storage
tank.
There should be no valving in this line. Damage to the
system caused by a blocked product water line will
not be covered by warranty.
4. Power cable with the proper gauge rating for this
system’s power consumption.
5. An electrical power source capable of supplying the
proper current and voltage to the system.
4.2 FINAL LIFT OF THE SKID INTO PLACE
1. Attach lift ropes to the top portion of the frame four
corner posts only. Use caution to protect the epoxy
coating with soft material. DO NOT attach guidelines
to, or handle the Parker Hannifi n System by any of
the piping, controls, or other components within the
System. Lift each skid into place.
2. Set the skid onto wood blocks in order to suspend it
above ground level while aligning mounting holes or
studs.
3. Lift the skid and remove the wood blocks from the
fi nal resting place. Once the skid is in its exact place
for installation gently set the skid down to rest and
secure it.
4. Secure the each skid in place using Vibration Isolators
as required.
4.3 INTERCONNECTING SKIDS
Refer to System Specifi cations regarding water line
capacities and electrical power consumption.
A. INSTALLING FLANGE PLUMBING
install the interconnecting hose or pipe to skid fl anges and
fi tting per
Table 4-1 on Page 4-3 .
B. INSTALLING COMPONENT PLUMBING
Install the component interconnecting tube per Table 4-2
on Page 4-3 .
D. INSTALLING COMPONENT WIRNG
install Booster Pump and HP Pump wiring to control box
Coral Sea Owner's Manual