Panasonic LP-M Series Скачать руководство пользователя

Страница: 87 / 174

Input signal operation in I/O connector

ンㄆㄇㄆㄓㄆㄏ㄄ㄆ

• The ON/OFF listed in this section refers to the ON/OFF operations. It does not refer to the voltage level (High/Low).

Terminal No. Name / Description

IN COM.: Input common

The common terminal for each input of the I/O terminal and I/O connector. This terminal is internally

connected to the input common on the input terminal block. It is not necessary to be connected if

connected at the input terminal block.

ワㄐㄕㄊ㄄ㄆ

• The inverting a power wiring of input/output terminal and I/O connector has trouble with the laser marker. Please make

sure to check the power wiring before running the laser marker.

SET: Set input

Turn this ON when executing the number input selected at the number input (D0 to D15) and the select

input (SELECT 0 to 2).

Turn the set input ON while maintaining the input status by specifying the SELECT 0 to 2 input and the

number input (D0 to D15). The input operation is executed at the timing of the edge of set input ON.

3 to 18

D0 to D15 : Number input

Set the number for one of the following targets selected at SELECT 0 to 2 input.

File No.

Count-up value correction

Count-down value correction

Counter number to reset

Data number for Rank /External offset function

For the select input method, refer to the description of terminal No. 20 to 22.

File No. (SELECT 0 to 2 input: All OFF)

Input when changing the file number of 0 to 2047.

Specify the file number in the binary system as D0 to D15 and turn ON the set input.

Indicate values in the binary system as ON/OFF of D0 to D15 with D0 being the lowest digit value.

Example: When selecting the file No. 618

Select “0000 0010 0110 1010”, which represents 618 in a 16-bit binary system, by specifying ON/OFF

of D0 to D15 as shown in the below table.

Terminal

File No. (binary)

INPUT

OFF

Terminal

File No. (binary)

INPUT

OFF

D10

OFF

D11

OFF

D12

OFF

D13

OFF

D14

OFF

D15

OFF

ME-LPM-SSM-10

Содержание LP-M Series















































































































































































Результаты поиска

Содержание LP-M Series

Отзывы:

Похожие инструкции для LP-M Series

Бренды по названию

Популярные бренды

Panasonic LP-M Series, Руководство по обслуживанию

Результаты поиска

Содержание LP-M Series

Отзывы:

Похожие инструкции для LP-M Series

Бренды по названию

Популярные бренды