Panasonic LP-M Series Скачать руководство пользователя

Страница: 59 / 174

2-4-2 Connecting ground and power supply

This section describes how to connect ground and power supply. For the AC power cable, use the attached AC power

cable. The power terminal, protective conductor terminal and frame ground terminal are located on the back side of the unit

as shown below.

Power

terminal

Power

terminal

Controller

LP-M200/M205/M500/M505

LP-MA00/MA05/MA06

Head

Protective conductor

terminal

Protective conductor

terminal

Frame ground

terminal: F.G.

WARNING

• Perform the connection of the Power Terminal Block with power-off state.

There is a risk of electrical shock.

Connect the protective conductor terminal and the frame
ground terminal to the grounding part.

Screw size: M4
Tightening torque: 1.0N·m

ワㄐㄕㄊ㄄ㄆ

• Before connecting the power supply, connect the protective conductor terminal and the frame ground terminal

permanently to the grounding part.

• Install such that the controller housing and the head housing are at the same electric potential.

Loosen two M3 screws of the power terminal casing and remove
it.

Remove the resin cover on the terminal.

Protective conductor terminal /

Frame ground terminal

Ground

Terminal

Resin cover

ME-LPM-SSM-10

Содержание LP-M Series















































































































































































Результаты поиска

Содержание LP-M Series

Отзывы:

Похожие инструкции для LP-M Series

Бренды по названию

Популярные бренды

Panasonic LP-M Series, Руководство по обслуживанию

Результаты поиска

Содержание LP-M Series

Отзывы:

Похожие инструкции для LP-M Series

Бренды по названию

Популярные бренды