Palamides 102-13 Скачать руководство пользователя страница 59

Страница: 59 / 68

Error list TC166

Subject to change without notice

Error
nr.

Conditions

In- /
Output

Description Possible

Causes

13 Machine

Start

Packing cycle

B35 oder
B36

Side loader is not in the normal position

1. Paper jam in the vicinity of the side loader
2. Side loader too slow
3. Sensor defective

4.  Side loader is not connected
5.  Air hose is not connected
6.  Air pressure too low

Input IN03.8 / IN3.13 problem

14 Machine

Start

Packing cycle

B38

Lifting table is not in the normal position

1. Paper jam in the vicinity of the package lift
2. Sensor defective

3.  Package lift too slow
4.  Package lift plug loose or not connected
5.  Air hose is not connected
6.  Air pressure too low

Input IN03.9 problem

15 Machine

Start

Packing cycle

B39

Package lift ejector is not in the normal position

1. Paper jam in the vicinity of the package lift
2. Sensor defective

16 Machine

Start

Packing cycle

B3/Y7

The pressing bars need more than 2 seconds to move
into the shaft

1.  Paper jam in front of pressing bars
2.  Air pressure too low
3.  Sensor defective or wrongly adjusted
4.  Support pressing bars moving against jogging

plates

17 Machine

Start

Packing cycle

Elevation table moves right to the top during packing
cycle; Protection of welding dies

1. No stack or too small a stack

2. Sensor B14 defective or malfunctioning

18 Machine

Start

Welding

Welding process takes too long

1. Relay K7 defective
2. Relay K5 defective or wrongly adjusted (1.0)

Code 121 wrongly adjusted (2000)

20 Machine

Start

Packing cycle

B18/B15

Elevation table does not stop at the intermediate
position, but continues to move right down

1. Photocell B18 positioned in the wrong place
2. Paper jam in the vicinity of photocell B18
3. Photocell B18

or its cable

defective

4. Sensor B15 covered or defective

Map Device

Shaft protection with map device

1. Paper jam in the shaft
2. Sensor B100/101/102 or its cable defective

Input IN03.6 problem

Содержание 102-13





































































Результаты поиска

Содержание 102-13

Отзывы:

Похожие инструкции для 102-13

Бренды по названию

Популярные бренды

Palamides 102-13, Руководство по эксплуатации

Результаты поиска

Содержание 102-13

Отзывы:

Похожие инструкции для 102-13

Бренды по названию

Популярные бренды