manualshive.com logo in svg

Palamides 102-13, Руководство по эксплуатации

Поделиться
Скачать
Palamides 102-13 Скачать руководство пользователя страница 10

2 

Fundamental Safety Advice

 

10 

Subject to change without notice

 

2 Fundamental 

Safety 

Advice 

2.1 

Warning advice and symbols 

Throughout the operating instructions, the following designations, or rather signs are used for 
especially important statements: 
 
 

>TIP<

 

 

Special statements with regard to the economic 
application of the machine 
 

>ATTENTION!<

 

!

 

 

Special statements, or rather commands and 
prohibitions, to prevent damage. 
 

>Danger<

 

!

 

Statements, or rather commands and prohibitions, to 
prevent injury to persons or extensive damage to 
property 

 
 

2.2 

Safety at work 
Agreed application of the Automatic Delivery 

1.  At the time of supply, palamides Automatic Deliveries meet all safety-related regulations.  

For this purpose, moving and rotating parts are covered with safety hoods, which are 
mechanically, or rather, electrically locked in such a way that no unreasonable 
interference with the operation exists. 

2.  It is extremely important with all safety related measures that the operating personnel 

practice high safety levels and have remaining sources of danger pointed out to them 
and/or impairment of the machine and other material assets cannot be excluded. 

3.  The machine may be operated only when in perfect technical condition. Faults which may 

impair safety are to be removed immediately by trained personnel or personnel from the 
manufacturer and/or supplier. 

4.  The machine is only intended for banding folded paper. Banding of other materials  goes 

against agreement. The manufacturer and/or supplier is not responsible for any damage 
resulting from this. 

5.  Before you operate the machine, read carefully through all the operating instructions, 

including the safety and service conditions. 

6.  The operating instructions must always be handy near the machine. 

7.  If necessary, supplement the operating instructions with internal safety regulations, as 

well as with legal accident prevention regulations. 

8.  If machine personnel changes frequently, make sure that all machine operators are 

informed, or rather, trained in the previously mentioned points. 

9.  Never remove the protective, or rather safety devices on the machine and never alter the 

machine so that safety can no longer be guaranteed. 

Содержание 102-13





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды