manualshive.com logo in svg

Palamides 102-13, Руководство по эксплуатации

Поделиться
Скачать
Palamides 102-13 Скачать руководство пользователя страница 15

How to run the machine 

3

 

Subject to change without notice 

15

 

Group III 
 
 
 
 

 

 
 
 
 
 
 
 
 
 
 

(1) 

Starting position 

By pressing the starting position key, all movements since last 
pressing the start button will return to their original positions. 

Note: 

The “actual amount” on the batch counter will also be 

reset at Zero.  Please ensure that the shafts are free. The pre-
set batch amount stays the same. 

Note

: This key only reacts if the unit is at a standstill. 

(2) 

Running out 

By pressing the pack remainder key, a packing cycle will start 
and the unit will be emptied. 

Note

: This key only reacts if the unit is at a standstill. 

(3) 

Manual welding 

The manual welding key is used to connect the two loose ends 
of the band after the band has been exchanged or after a 
malfunction. Pressing the manual-welding key starts the 
following processes. 

1.  The elevation table moves to its lowest position. 
2.  The pressing rails and the welding die move into the 

shaft. 

3.  The welding process starts up. 
4.  The pressing rails and the welding die move again to 

their starting positions. 

Note

: Ensure that there is sufficient band between the welding 

dies before manual welding. 

Note

: This key only reacts if the unit is at a standstill 

(4) Elevation 

table 

downwards 

The elevation table downwards key is used to bring the 
elevation table down to its lowest position so that jammed 
product causing an error can be released. 

Note

: Ensure that the area under the elevation table is clear. 

Note

: This key only reacts if the unit is at a standstill. 

(5) 

Inspection 

When the inspection key is pressed, the next oncoming sheet 
will be ejected. 

(6) F1 

Free 

(7) 

F2 

When the F2 key is pressed, the actual test reading for 
monitoring of the format is shown on the display. 

(8) 

Side loader 

When the side loader key is pressed, the unit is filled with 
compressed air.  When the side loader key is pressed again, 
the loader moves to the opposite position. When the side 
loader key is pressed yet again, the side loader moves back to 

(6) 

(7) 

(8)

(10) 

(9)

(1) 

(2) 

(3)

(4)

(5)

Содержание 102-13





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды