Palamides 102-13 Скачать руководство пользователя страница 66

Страница: 66 / 68

Error list TC161

Subject to change without notice

Error
nr.

Conditions

In- /
Output

Description Possible

Causes

30 Machine

Start

Packing cycle

B14

Elevation table moves to starting position and takes too
long

6.  Elevation table system fault (Motor, FRQ, etc.)
7.  Parcel between pressing bars & elevation table
8.  Sensors B14 or B20 defective
9.  Input IN01.6 problem (B14)
10. Elevation table knocks against the jogging plates

(bent)

31 Machine

Start

Packing cycle

Time for extending welding die exceeded welding die
moves to working position

5. Paper between the welding dies
6. Air pressure
7. Sensor B2 defective or wrongly adjusted
8. Input IN03.2 problem

32 Machine

Start

Packing cycle

Time for retacting welding die exceeded welding die
moves to normal position

7. Defective cylinder
8. Air pressure
9. Obstacle
10. Sensor B1 defective or wrongly adjusted
11. Input IN03.1 problem
12. Linear bearing defective

34 Machine

Start

Open Guard

Drives turn at too high a speed during jogging
operation

4. Frequency converter defective
5. Tacho defective
6. Frequency converter set to wrong parameters

Destacking without
counter release

B12

Sensor B12 do not aware the product
batch counter does not count,
destacking sensor covered.

2.  Sensor B12/B19 defective
3.  Sensor B12/B19 not on the product
4.  Sensor B12/B19 wrongly adjusted

B41

Frequency converter pressing drive has switched off

3.  Fault with frequency converter A13
4.  Protective motor switch Q3 has switched off
5.  Further information on the FU-Display

B42

Frequency converter belt drive has switched off

3.  Fault with frequency converter A14
4.  Protective motor switch Q3 has switched off
5.  Further information on the FU-Display

B43

Frequency converter elevator table drive has switched
off

3.  Fault with frequency converter A15
4.  Protective motor switch Q3 has switched off
5.  Further information on the FU-Display

Содержание 102-13





































































Результаты поиска

Содержание 102-13

Отзывы:

Похожие инструкции для 102-13

Бренды по названию

Популярные бренды

Palamides 102-13, Руководство по эксплуатации

Результаты поиска

Содержание 102-13

Отзывы:

Похожие инструкции для 102-13

Бренды по названию

Популярные бренды