Palamides 102-13 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 68

background image

How to run the machine

3

Subject to change without notice

13

(3)

Stop button

Switches off the machine
Erases errors. When a fault has been removed mechanically,
the error message will still be shown on the display. After the
Stop button has been pressed, this message will be erased.

Note:

None of the data is erased when the Stop button is

pressed. This means that, after a new start, work continues
from the same position where it stopped before the Stop button
was activated.

(4)

Start button

Starts the machine

Note:

After pressing the start button, the equipment still needs

a few seconds before it is operational. During this time, any
products coming along will be ejected via the waste sheet
deflector.

(5)

Sheet input button

This button only has a function if the BA700 has been
connected either to an MBO folding machine using a standard
(24-pole) plug, or to a Stahl folding machine using a Stahl
interface.

Connection with MBO:

By pressing the sheet-input button

once, the sheet supply on the folding machine’s feeder is
switched on. By pressing the sheet-input button again the
sheet supply is switched off.

Connection with Stahl:

By pressing the sheet-input button,

the sheet supply on the folding machine’s feeder is switched
on. Pressing the sheet input button again has no effect.

(6)

Single sheet button

This button only has a function if the BA700 has been
connected either to an MBO folding machine using a standard
(24 pole) plug, or to a Stahl folding machine using a Stahl
interface.

Connection with MBO:

By pressing the single sheet button,

one single sheet will be delivered by the folding machine’s
feeder.

Connection with Stahl:

By pressing the single sheet button,

the sheet supply from the folding machine’s feeder is switched
off. Pressing the sheet input button again has no effect.

(7)

Potentiometer 1

The speed of the transport belts, which lead from the press
station to the shaft, can be altered by using the potentiometer’s
regulator.

(8)

Potentiometer 2

The speed of the round belts, which lead to the press station,
can be altered by using the potentiometer’s regulator. The
speed is shown in metres per minute on the upper right-hand
side of the display.

«
...
11
12
13
14
15
...
»

Содержание 102-13





































































Отзывы:

Нет отзывов

Похожие инструкции для 102-13

Бренд: ZOLL Страницы: 344

Бренд: ABB Страницы: 9

Бренд: Panasonic Страницы: 30

Бренд: ACE INSTRUMENTS Страницы: 15

Бренд: Wave Fitness Страницы: 15

Бренд: CAB Страницы: 13

Бренд: CAB Страницы: 30

Бренд: CAB Страницы: 17

Бренд: CAB Страницы: 33

Camping Equipment

Бренд: C. Crane Страницы: 8

Бренд: C-Pro Direct Страницы: 4

Бренд: C-Pro Direct Страницы: 4

Бренд: Laserworld Страницы: 8

Бренд: Laserworld Страницы: 6

Бренд: LaserLiner Страницы: 56

Бренд: LaserLiner Страницы: 54

Бренд: Maeda Страницы: 276

Бренд: MacDon Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды