Palamides 102-13 Скачать руководство пользователя страница 53

Страница: 53 / 68

Code list TC166

Subject to change without notice

Code
nr.

Password
protected

Set
value

Unit Title

Description

135

136 no

Set-up

time

137 yes 0

not active
active

Cycle time reduction - Welding heads starts as the same time as elevation table "up".

140

Display for actual sheet length

141

Display for the result of the measurement of the last bad sheets.

142

m/min

Display for the speed of the transport belts

143

date

Last software change

144

yes

1/1000 sec

Delay 12

Welding time monitoring - if the heating dies are heated for a long time, the machine is
stopped with Error 18

145

Display for cycles until machine stops with Error 42 running out of banding.

150 yes 0

not active
active

By activating Total Reset, all memory will be deleted. All variable values will be deleted. All
code values will return to basic setup

170 no 0

Operating mode paper banding
Operating mode plastic PE-banding

171

1/100 sec

Delay 13

Heating time for PE-banding

172

1/100 sec

Delay 14

Cutting time for PE-banding

173

100

1/100 sec

Delay 15

Cooling time for PE-banding

175

yes

Delay 17

Starting delay for small-package facility

176

yes

Delay 18

Switch-off delay for small-package facility

203

Input display - Inputs can be checked during operation using cursor up / cursor down keys

204

Output display - Outputs can be checked during operation using cursor up / cursor down
keys

Содержание 102-13





































































Результаты поиска

Содержание 102-13

Отзывы:

Бренды по названию

Популярные бренды

Palamides 102-13, Руководство по эксплуатации

Результаты поиска

Содержание 102-13

Отзывы:

Бренды по названию

Популярные бренды