Oracle SPARC T8-2 Скачать руководство пользователя

Страница: 59 / 188

Remove the Server From the Rack

Remove the Server From the Rack

You must remove the server from the rack to remove or install these components:

■

Motherboard

■

PS backplane

■

Drive backplane

Caution -

The server chassis is heavy. To avoid personal injury, use two people to remove the

server from the rack.

Shut down the host.

Remove power from the server.

See

“Removing Power From the Server” on page 51

Disconnect all the cables and power cords from the server.

Extend the server to the maintenance position.

See

“Extend the Server to the Service Position” on page 55

Release the CMA from the rail assembly.

The CMA is still attached to the cabinet, but the server chassis is now disconnected from the

CMA. See

“Release the CMA” on page 57

From the front of the server, pull the release tabs forward and pull the server

forward until it is free of the rack rails.

A release tab is located on each rail.

Set the server on a sturdy work surface.

Remove the top cover.

See

“Remove the Top Cover” on page 60

Related Information

■

“Extend the Server to the Service Position” on page 55

■

“Release the CMA” on page 57

■

“Remove the Top Cover” on page 60

Preparing for Service

Содержание SPARC T8-2





























































































































































































Результаты поиска

Содержание SPARC T8-2

Отзывы:

Похожие инструкции для SPARC T8-2

Бренды по названию

Популярные бренды

Oracle SPARC T8-2, Руководство по обслуживанию

Результаты поиска

Содержание SPARC T8-2

Отзывы:

Похожие инструкции для SPARC T8-2

Бренды по названию

Популярные бренды