Oracle SPARC T8-2 Скачать руководство пользователя страница 94

Страница: 94 / 188

Locating and Replacing a Faulty DIMM

Review the

memory riser and DIMM configuration rules

Prepare the system for service

Unplug the power cords

Remove the memory risers

Remove any DIMM fillers

installed on the memory risers.

Determine your upgrade path.

■

If you are adding DIMMs to the memory risers only, ensure the new DIMMs

have the

same rank classification

as the DIMMs already installed on the

motherboard.

■

If you are upgrading all of the memory in the server,

remove all of the

existing DIMMs

on the memory risers and the motherboard.

Install the new DIMMs

Install the memory risers

Return the server to operation

10.

Enable and verify

the new DIMMs.

Locating and Replacing a Faulty DIMM

You can locate a failed DIMM either by using the

Oracle ILOM show faulty command

, or with

the

DIMM fault LEDs

located on the motherboard and the memory risers. Locate the memory

risers using the

“Server Top View” on page 16

After locating and

removing

the faulty DIMM,

install

and

verify

the replacement DIMM.

Locate a Faulty DIMM (Oracle ILOM)

The Oracle ILOM

show faulty

command displays current faults, including DIMM failures.

SPARC T8-2 Server Service Manual • June 2019

Содержание SPARC T8-2





























































































































































































Результаты поиска

Содержание SPARC T8-2

Отзывы:

Похожие инструкции для SPARC T8-2

Бренды по названию

Популярные бренды

Oracle SPARC T8-2, Руководство по обслуживанию

Результаты поиска

Содержание SPARC T8-2

Отзывы:

Похожие инструкции для SPARC T8-2

Бренды по названию

Популярные бренды