Oracle SPARC T8-2 Скачать руководство пользователя страница 97

Страница: 97 / 188

Replace a Faulty DIMM

■

“Remove a DIMM” on page 100

■

“Server Top View” on page 16

Replace a Faulty DIMM

Caution -

This procedure requires handling components that are sensitive to ESD.

antistatic practices

to avoid damage or component failure.

Customers can perform this procedure, but the system must first be completely powered down

and all power cords unplugged. See

“Component Service Categories” on page 48

for more

information about cold-service procedures.

Perform this procedure to replace a faulty DIMM on the motherboard or a memory riser.

Identify the faulty DIMM

to be removed using the ILOM

show faulty

command.

Prepare the system for service

Unplug the power cords

Remove the appropriate memory riser

To remove a DIMM from the motherboard, you must remove the memory riser above that

DIMM to enable access.

Locate the faulty DIMM

on the motherboard or memory riser using the DIMM

fault LEDs.

Remove the faulty DIMM

Ensure the replacement DIMM has the

same rank classification

as the faulty

DIMM.

Install the replacement DIMM

Install the memory riser

that you removed.

10.

Return the server to operation

11.

Enable and verify

the replacement DIMM.

Servicing Memory Risers and DIMMs

Содержание SPARC T8-2





























































































































































































Результаты поиска

Содержание SPARC T8-2

Отзывы:

Похожие инструкции для SPARC T8-2

Бренды по названию

Популярные бренды

Oracle SPARC T8-2, Руководство по обслуживанию

Результаты поиска

Содержание SPARC T8-2

Отзывы:

Похожие инструкции для SPARC T8-2

Бренды по названию

Популярные бренды