Oracle SPARC T8-2 Скачать руководство пользователя страница 108

Страница: 108 / 188

Enable and Verify a DIMM

0:0:0>POST: Return to VBSC.
0:0:0>Master set ACK for vbsc runpost command and spin...

Note -

The server might boot automatically at this point. If so, go to step f. If the server remains

at the OpenBoot prompt (

) go to the next step.

If the server remains at the OpenBoot prompt, type

boot

Return the virtual keyswitch to Normal mode.

set /HOST keyswitch_state=Normal

Set 'keyswitch_state' to 'Normal'

Switch to the system console and type:

fmadm faulty

If any faults are reported, refer to the diagnostics instructions described in

“Identify

Faulted Components” on page 29

Switch to the Oracle ILOM command shell.

Type:

show faulty

If the

show faulty

command reports a fault with a UUID go to the next step. If

show faulty

does

not

report a fault with a UUID, you are done with the verification process.

Switch to the system console and type the

fmadm repair

command with the UUID.

Use the same UUID that was displayed from the output of the Oracle ILOM

show faulty

command.

fmadm repair 7c7efb20-3333-e2d7-b8ea-986b3e9dbaa9

108

SPARC T8-2 Server Service Manual • June 2019

Содержание SPARC T8-2





























































































































































































Результаты поиска

Содержание SPARC T8-2

Отзывы:

Похожие инструкции для SPARC T8-2

Бренды по названию

Популярные бренды

Oracle SPARC T8-2, Руководство по обслуживанию

Результаты поиска

Содержание SPARC T8-2

Отзывы:

Похожие инструкции для SPARC T8-2

Бренды по названию

Популярные бренды