Oracle SPARC T8-2 Скачать руководство пользователя

Страница: 134 / 188

Verify the SPM

For information about initializing TPM using the Oracle ILOM interface to enable failover,

see

Securing Systems and Attached Devices in Oracle Solaris 11.3

Restore the TPM data and keys that were backed up to the new SP you

install.

For information about migrating or restoring TPM data and keys, see

Securing Systems

and Attached Devices in Oracle Solaris 11.3

11.

Power on the server.

See

“Power On the Server (Oracle ILOM)” on page 174

“Power On the Server (System

Power Button)” on page 175

12.

Verify the SPM.

See

“Verify the SPM” on page 134

Related Information

■

Oracle ILOM documentation

■

“Remove the SPM” on page 130

■

“Verify the SPM” on page 134

Verify the SPM

Verify that the SPM Status LED is illuminated green.

The LED flashes green while the SPM initializes the Oracle ILOM firmware. See

“Interpreting

LEDs” on page 33

for information about the status of the SPM LED.

At the Oracle ILOM prompt, start the fault management shell.

start /SP/faultmgmt/shell

Are you sure you want to start /SP/faultmgmt/shell (y/n)?

faultmgmtsp>

Type

fmadm faulty

to check for faults.

■

If faults are reported, see

“Detecting and Managing Faults” on page 27

■

If no faults are reported, then the SPM has been replaced successfully.

134

SPARC T8-2 Server Service Manual • June 2019

Содержание SPARC T8-2





























































































































































































Результаты поиска

Содержание SPARC T8-2

Отзывы:

Похожие инструкции для SPARC T8-2

Бренды по названию

Популярные бренды

Oracle SPARC T8-2, Руководство по обслуживанию

Результаты поиска

Содержание SPARC T8-2

Отзывы:

Похожие инструкции для SPARC T8-2

Бренды по названию

Популярные бренды