Oracle SPARC T8-2 Скачать руководство пользователя страница 36

Страница: 36 / 188

Interpreting LEDs

Rear Panel Controls and LEDs

No.

LED

Icon or Label

Description

PS AC OK LED

Indicates these conditions:

■

Off

– No AC power applied to this power supply.

■

Green steady on

– AC power is applied to this power supply and is

within specifications.

■

Amber steady on

– AC power is applied to this power supply and

is below 85V.

PS DC OK LED (green)

Indicates these conditions:

■

Off

– 12V DC output from this power supply is disabled or not

within specification.

■

Steady on

– 12V DC output from this power supply is present and

within specifications.

PS Fault LED (amber)

Indicates these conditions:

■

Off

– Steady state, no service action is required.

■

Steady on

– A fault has been detected on this power supply.

NET MGT Port Link and

Activity LED (green on left)

NET MGT Port Speed LED

(green on right)

LINK/ACT

SPD

Indicates these conditions:

■

Off

– No link is established.

■

Steady On

– A link is established.

■

Blinking

– A link is established and there is activity on the port.

Indicates these conditions:

SPARC T8-2 Server Service Manual • June 2019

Содержание SPARC T8-2





























































































































































































Результаты поиска

Содержание SPARC T8-2

Отзывы:

Похожие инструкции для SPARC T8-2

Бренды по названию

Популярные бренды

Oracle SPARC T8-2, Руководство по обслуживанию

Результаты поиска

Содержание SPARC T8-2

Отзывы:

Похожие инструкции для SPARC T8-2

Бренды по названию

Популярные бренды