Oracle SPARC T8-2 Скачать руководство пользователя

Страница: 61 / 188

Attaching Devices During Service

Related Information

■

“Replace the Top Cover” on page 172

■

“Extend the Server to the Service Position” on page 55

■

“Release the CMA” on page 57

■

“Remove the Top Cover” on page 60

Attaching Devices During Service

During service procedures, you might have to connect devices to the server.

■

For OS support, connect an Ethernet cable to the one of the Ethernet connectors (NET 0,

NET 1, NET 2, and NET 3).

■

If you plan to interact with the system console directly, you can connect additional external

devices, such as a mouse and keyboard, to the server's USB connectors, and connect a

monitor to a DB-15 video connector. The front DB-15 video connector is active by default.

To enable the rear port and disable the front port, you must enable the Oracle ILOM

VGA_REAR_PORT

policy:

set /SP/policy VGA_REAR_PORT=enabled

. For more details on

selecting an active video port, refer to

“Accessing the Server” in

SPARC T8 Series Servers

Administration Guide

■

If you plan to connect to the Oracle ILOM software over the network, connect an Ethernet

cable to the Ethernet port labeled NET MGT.

Note -

The SPM uses the NET MGT (out-of-band) port by default. You can configure

the SPM to share one of the sever's four Ethernet ports instead. The SPM uses only the

configured Ethernet port.

■

If you plan to access the Oracle ILOM CLI through the SER MGT port, connect a serial null

modem cable to the RJ-45 serial port labeled SER MGT.

■

The USB connectors on the front panel support USB 2.0. The USB connectors on the rear

panel support USB 3.0.

Related Information

■

“Front Panel Components (Service)” on page 13

■

“Rear Panel Components (Service)” on page 15

■

“Detecting and Managing Faults” on page 27

■

Server Installation

Preparing for Service

Содержание SPARC T8-2





























































































































































































Результаты поиска

Содержание SPARC T8-2

Отзывы:

Похожие инструкции для SPARC T8-2

Бренды по названию

Популярные бренды

Oracle SPARC T8-2, Руководство по обслуживанию

Результаты поиска

Содержание SPARC T8-2

Отзывы:

Похожие инструкции для SPARC T8-2

Бренды по названию

Популярные бренды