Oracle SPARC T8-2 Скачать руководство пользователя страница 147

Страница: 147 / 188

Servicing the Motherboard

The motherboard includes two CMP modules, two MR I/O modules, memory control

subsystems, host ID/MAC addresses, and all SPM (Oracle ILOM) logic. The host ID and all

MAC addresses reside on a removable SCC PROM. Oracle ILOM system configuration data

resides on the service processor module (SPM).

The motherboard also hosts the PS backplane, which distributes main 12V power from

the power supplies to the rest of the server. The PS backplane is connected directly to the

motherboard through a bus bar and ribbon cable, and includes a top cover safety interlock

switch.

These topics describe how to service the motherboard.

■

“Remove the Motherboard” on page 147

■

“Install the Motherboard” on page 151

■

“Reactivate RAID Volumes” on page 155

■

“Verify the Motherboard” on page 158

Related Information

■

“Component Service Categories” on page 48

■

“Servicing the SPM” on page 129

Remove the Motherboard

This is a cold-service procedure that must be performed by qualified service personnel. Power

down the server completely before performing this procedure.

Caution -

Ensure that all power is removed from the server before removing or installing

the motherboard assembly. You must disconnect the power cables from the server before

performing these procedures.

Servicing the Motherboard

147

Содержание SPARC T8-2





























































































































































































Результаты поиска

Содержание SPARC T8-2

Отзывы:

Бренды по названию

Популярные бренды

Oracle SPARC T8-2, Руководство по обслуживанию

Результаты поиска

Содержание SPARC T8-2

Отзывы:

Бренды по названию

Популярные бренды