Oracle SPARC T8-2 Скачать руководство пользователя страница 39

Страница: 39 / 188

View Log Files (Oracle ILOM)

The

/var/adm

directory contains several message files. The most recent messages are in

the /

var/adm/messages

file. After a period of time (usually every week), a new

messages

file is automatically created. The original contents of the

messages

file are rotated to a file

named

messages.1

. Over a period of time, the messages are further rotated to

messages.2

and

messages.3

, and then deleted.

Log in as superuser.

Type:

more /var/adm/messages

To view all logged messages, type:

more /var/adm/messages*

Related Information

■

“Check the Message Buffer” on page 38

■

“View Log Files (Oracle Solaris)” on page 38

■

“POST Overview” on page 40

View Log Files (Oracle ILOM)

View the event log.

show /SP/logs/event/list

View the audit log.

show /SP/logs/audit/list

Related Information

■

“Check the Message Buffer” on page 38

■

“View Log Files (Oracle Solaris)” on page 38

Detecting and Managing Faults

Содержание SPARC T8-2





























































































































































































Результаты поиска

Содержание SPARC T8-2

Отзывы:

Похожие инструкции для SPARC T8-2

Бренды по названию

Популярные бренды

Oracle SPARC T8-2, Руководство по обслуживанию

Результаты поиска

Содержание SPARC T8-2

Отзывы:

Похожие инструкции для SPARC T8-2

Бренды по названию

Популярные бренды