Oracle SPARC T8-2 Скачать руководство пользователя

Страница: 149 / 188

Remove the Motherboard

You will reinstall the eUSB drive on the new motherboard. See

“Remove the eUSB

Drive” on page 115

Remove all memory risers.

See

“Remove a DIMM” on page 100

Remove the System Remind button assembly (air divider) by lifting it up and

away from the power supplies.

Disconnect all cables connected to the motherboard.

Disconnect two longer cables that connect the motherboard to the drive

backplane.

Push down a metal tab on each connector and pull up.

Disconnect two shorter cables from the motherboard.

One cable goes to the drive backplane. The other is a ribbon cable to the power supply.

Disconnect the fan board power cable and the ribbon cable from the

motherboard.

Caution -

When removing the ribbon cable from the motherboard, grasp the cable connector on

either side and pull straight up to disconnect the cable.

Do not

rock the cable side to side. Doing

so could damage the connector.

If necessary, disconnect the four NVMe drive cables from the drive

backplane.

Note the order in which the cables are connected, you must reinstall them into the same

connectors.

10.

Remove the power supply cover.

You must guide two slots on the PS backplane cover around two pins on the inside of the power

supply cage.

Lift the cover up a little to clear the first part of the slots.

Pull the cover a little towards the front of the chassis.

Push the tooth at the bottom of the cover to clear the edge of the power

supply cage.

Servicing the Motherboard

149

Содержание SPARC T8-2





























































































































































































Результаты поиска

Содержание SPARC T8-2

Отзывы:

Похожие инструкции для SPARC T8-2

Бренды по названию

Популярные бренды

Oracle SPARC T8-2, Руководство по обслуживанию

Результаты поиска

Содержание SPARC T8-2

Отзывы:

Похожие инструкции для SPARC T8-2

Бренды по названию

Популярные бренды