Oracle SPARC T8-2 Скачать руководство пользователя

Страница: 60 / 188

Remove the Top Cover

Remove the Top Cover

Caution -

Removing the top cover without properly powering down the server and

disconnecting the AC power cords from the power supplies results in a chassis intrusion switch

failure. This failure causes the server to be immediately powered off. Any changes you make

to the memory riser or DIMM configurations will not be properly reflected in the service

processor's inventory until you replace the top cover.

Ensure that the AC power cords are disconnected from the server power

supplies.

Unlatch the server top cover.

Insert your fingers under the two cover latches and simultaneously lift both latches in an

upward motion as shown in panel 1.

Lift the cover slightly and slide it toward the front of the server chassis about 0.5

inch (12 mm).

Lift up and remove the top cover as shown in panel 2.

A metal air baffle is attached to the rear inside surface of the top cover. When you remove the

top cover, lift it carefully so that the air baffle does not catch on anything inside the server.

Service components as necessary.

SPARC T8-2 Server Service Manual • June 2019

Содержание SPARC T8-2





























































































































































































Результаты поиска

Содержание SPARC T8-2

Отзывы:

Похожие инструкции для SPARC T8-2

Бренды по названию

Популярные бренды

Oracle SPARC T8-2, Руководство по обслуживанию

Результаты поиска

Содержание SPARC T8-2

Отзывы:

Похожие инструкции для SPARC T8-2

Бренды по названию

Популярные бренды