Oracle SPARC T8-2 Скачать руководство пользователя

Страница: 45 / 188

Preparing for Service

These topics explain how to prepare the server for servicing.

Note -

Use only SPARC T8 components in SPARC T8 servers.

Step

Description

Links

Review safety and handling information.

“Safety Information” on page 45

Gather the tools needed for service.

“Tools Needed For Service” on page 47

Consider filler options.

“Fillers” on page 47

Review component service categories.

“Component Service Categories” on page 48

Find the server serial number.

“Find the Server Serial Number” on page 49

Identify the server to be serviced.

“Locate the Server” on page 50

For cold-service operations, shut down the OS and remove

power from the server.

“Removing Power From the Server” on page 51

Move the server out of the rack and gain access to internal

components.

“Accessing Server Components” on page 54

Attach devices to the server to perform service procedures.

“Attaching Devices During Service” on page 61

Related Information

■

“Identifying Components” on page 13

■

“Returning the Server to Operation” on page 171

Safety Information

For your protection, observe the following safety precautions when setting up your equipment:

■

Follow all cautions and instructions marked on the equipment and described in the

documentation shipped with your server.

Preparing for Service

Содержание SPARC T8-2





























































































































































































Результаты поиска

Содержание SPARC T8-2

Отзывы:

Похожие инструкции для SPARC T8-2

Бренды по названию

Популярные бренды

Oracle SPARC T8-2, Руководство по обслуживанию

Результаты поиска

Содержание SPARC T8-2

Отзывы:

Похожие инструкции для SPARC T8-2

Бренды по названию

Популярные бренды