Oracle SPARC T8-2 Скачать руководство пользователя страница 51

Страница: 51 / 188

Removing Power From the Server

Removing Power From the Server

Step

Description

Links

Prepare the server for powering off.

“Prepare to Power Off the Server” on page 51

Power off the server by one of three methods.

“Power Off the Server (Oracle ILOM)” on page 52

“Power Off the Server (Server Power Button -

Graceful)” on page 53

“Power Off the Server (Emergency

Shutdown)” on page 53

Disconnect the power cords from the server.

“Disconnect Power Cords” on page 54

Related Information

■

“Front Panel Components (Service)” on page 13

■

Servers Administration

Prepare to Power Off the Server

Perform this procedure before powering off the server.

Log in as superuser or equivalent.

Depending on the type of problem, you might want to view server status or log files. You also

might want to run diagnostics before you shut down the server.

Notify affected users that the server will be shut down.

Refer to the Oracle Solaris system administration documentation for additional information.

Save any open files and quit all running programs.

Refer to your application documentation for specific information on these processes.

Shut down all logical domains.

Refer to Oracle Solaris system administration and Oracle VM Server for SPARC documentation

for additional information.

Shut down the Oracle Solaris OS.

Refer to the Oracle Solaris system administration documentation for additional information.

Preparing for Service

Содержание SPARC T8-2





























































































































































































Результаты поиска

Содержание SPARC T8-2

Отзывы:

Похожие инструкции для SPARC T8-2

Бренды по названию

Популярные бренды

Oracle SPARC T8-2, Руководство по обслуживанию

Результаты поиска

Содержание SPARC T8-2

Отзывы:

Похожие инструкции для SPARC T8-2

Бренды по названию

Популярные бренды