Optek CONTROL 200, Инструкция по эксплуатации

Страница: 30 / 135

C200 S
OFTWARE
Instruction Manual C200 Part2 A1.doc optek Danulat GmbH • D-45356 Essen • Germany page 8
2 Operation
2.1 Operation pH
2.1.1 Menu structure
Key
VIEW SETPOINTS VIEW OUTPUTS VIEW HARDWARE VIEW SOFTWARE
A1: Setpoint Analog Output 1 Sensor A Module AX400/2000 Issue
A2: Setpoint Analog Output 2 Sensor B Module
A3: Setpoint Analog Output 3 Option Board
A4: Setpoint Analog Output 4
A5: Setpoint
SECURITY CODE
CONFIG. DISPLAY Set Language Set Temp. Units Set Backlight
LED Backlight Temp. Units English
Use the Sidescroll Key to scroll through the Pages within each Menu
To
CONFIG. ALARMS
(see Fig. 2.3B)
Use the Downscroll
Key to scroll through
the Frames
within each Page
OPERATING PAGE
Section 2.3, Page 6 Section 3.1, Page 12 Section 3.2, Page 14 Section 3.3, Page 14 Section 3.4, Page 15 Section 3.5, Page 16
Section 5.1, Page 28
Section 5.2, Page 29
Section 3.6, Page 18
Alarms
Errors
Power
Cals
VIEW LOGBOOK
Dual input analyzer only
VIEW CLOCK
Date 01:01:03
Time 12:00
*
Applicable only if
Probe Type
is set to
Redox
or
ORP
CONFIG.DIAGS
Section 5.4, Page 33
Config. Sensor A
A: pH Glass
A: Ref. Checking
A: Ref. Alarm
Config. Sensor A Config. Sensor B
B: pH Glass
B: Ref. Checking
B: Ref. Alarm
Use the Menu Key
to scroll through
the Menus
CONFIG.SENSORS
B: Probe Type
B: Diff. Input
B: Electrode
B: Temp. Comp
B: Temp. Sensor
B: Preset Temp.
B: Sample Comp.
B: Sample Coeff.
Section 5.3, Page 30
B: Set Min Slope
Config. Sensor B
Config. Sensor A
A: Probe Type
A: Diff. Input
A: Temp. Comp
A: Temp. Sensor
A: Preset Temp.
A: Sample Comp.
A: Sample Coeff.
A: Set Min Slope
A: Electrode
A: Enable Cals B: Enable Cals * *
SENSOR CAL. Cal. User Code Sensor Cal. A
A: Buffer Method
A: Immerse Buf.1
A: Cal. Buffer 1
A: Immerse Buf.2
A: Cal. Buffer 2
A: Calibration
Section 4.1, Page 19
Set Auto Buffers
Buffer Type
Set Buffer 1
Set Buffer 2
A: Slope & Check
Sensor Cal. B
B: Buffer Method
B: Immerse Buf.1
B: Cal. Buffer 1
B: Immerse Buf.2
B: Cal. Buffer 2
B: Calibration
B: Slope & Check
A: Enter Point 1
A: Enter Point 2
B: Enter Point 1
A: Enter Point 5
A: Enter Point 4
A: Enter Point 3
B: Enter Point 2
B: Enter Point 5
B: Enter Point 4
B: Enter Point 3
#### 100% ####
#### 100% ####
#### 100% ####
#### 100% ####
Note. Sensor calibration parameters shown above
are for Automatic, 2-point calibration only. For other
calibration options, refer to Section 4.1.
Available only if the Option Board is fitted
and Analog features enabled – see Section 7.3
2.1.2, Page 10 3.1.1, Page 20 3.1.2, Page 20 3.2.3, Page 28 3.2.4, Page 29 3.1.5, Page 24 3.2.6, Page 31
4.1, Page 32
5.1.1, Page 43
5.1.2, Page 44
5.1.3, Page 45
5.1.4, Page 46