Optek CONTROL 200, Инструкция по эксплуатации

Страница: 38 / 135

C200 S
OFTWARE
Instruction Manual C200 Part2 A1.doc optek Danulat GmbH • D-45356 Essen • Germany page 16
2.2 Operation conductivity
2.2.1 Menu structure
To CONFIG. OUTPUTS
(see Fig. 2.3B)
SENSOR CAL. Cal. User Code
Section 4.1, Page 13
SECURITY CODE
Section 5.1, Page 15
CONFIG. DISPLAY Set Language Set Temp. Units Set Backlight
LED Backlight Temp. Units English
Section 5.2, Page 16
Available only if option board fitted and
analog features enabled – see Section 7.3
Key
Dual input analyzer only
Sensor Cal. B
B: Calibration
B: Sensor Slope
B: Sensor Offset
B: Temp. Slope
B: Temp. Offset
B: Reset?
Sensor Cal. A
A: Calibration
A: Sensor Slope
A: Sensor Offset
A: Temp. Slope
A: Temp. Offset
A: Reset?
Use the Sidescroll Key to scroll through the Pages within each Menu
VIEW SETPOINTS VIEW OUTPUTS VIEW HARDWARE VIEW SOFTWARE
A1: Setpoint Analog Output 1 Sensor A Module AX400/2000 Issue
A2: Setpoint Analog Output 2 Sensor B Module
A3: Setpoint Analog Output 3 Option Board
A4: Setpoint Analog Output 4
A5: Setpoint
Use the Downscroll
Key to scroll through
the Frames
within each Page
OPERATING PAGE
Section 2.3, Page 6 Section 3.1, Page 8 Section 3.2, Page 9 Section 3.3, Page 9 Section 3.4, Page 10 Section 3.5, Page 10 Section 3.6, Page 12
Alarms
Errors
Power
Cals
VIEW LOGBOOK VIEW CLOCK
Date 01:01:03
Time 12:00
Use the Menu Key
to scroll through
the Menus
CONFIG.SENSORS
Section 5.3, Page 17
Config. Sensor A
A: Sensor Group
A: Analyzer Type
A: Temp.Comp.
A: Temp.Sensor
B: Sensor Group
B: Analyzer Type
B: Temp.Sensor
B: Temp.Comp.
Config. Sensor B
B: Temp.Coeff A: Temp.Coeff
Note. The sensor configuration frames shown at left are those displayed
when the analyzer is set to its factory default settings. Other frames
are displayed depending on the Analyzer Type and Temp.Sensor settings
– see Section 5.3 page 17.
CONFIG.ALARMS Config. Alarm 1
A1: Type
A1: Assign
A1: Failsafe
A1: Action
A1: Setpoint
A1: Hysteresis
A1: Delay
Config. Alarm 2
A2: Type
A2: Assign
A2: Failsafe
A2: Action
A2: Setpoint
A2: Hysteresis
A2: Delay
A3: Assign
A3: Failsafe
A3: Action
A3: Setpoint
A3: Hysteresis
A3: Delay
Config. Alarm 3
A3: Type
Section 5.4, Page 24
Config. Alarm 4
A4: Type
A4: Assign
A4: Failsafe
A4: Action
A4: Setpoint
A4: Hysteresis
A4: Delay
Config. Alarm 5
A5: Type
A5: Assign
A5: Failsafe
A5: Action
A5: Setpoint
A5: Hysteresis
A5: Delay
2.2.2, Page 18 3.2.1, Page 27 3.2.2, Page 28 3.2.3, Page 28 3.2.4, Page 29 3.2.5, Page 29 3.2.6, Page 31
4.4, Page 41
5.2.1, Page 59
5.2.2, Page 60
5.2.3, Page 61
5.2.4, Page 68
5.2.3, Page 61