4 - 19
4 Remote I/O
CompoNet Communications Unit User’s Manual (I582-E1)
4-4 Sp
ecial I/O and
Flexi
ble F
o
rmat
4
4-
4-2 Special I/O (
100/150)
Precautions for Correct Use
Precautions for Correct Use
The Register No. and read/write data are the same as those for Modbus communication. For
these settings, refer to Section 6-8 Modbus Communication (Modbus-RTU) Data List of the
MX2 User's Manual (Cat. No. I570) and 8-5 Modbus Communication Register Number List of
the RX User's Manual (Cat. No. I578).
The error codes for the Special IO operation are listed below.
Special Remote Input Error Codes
Precautions for Correct Use
Precautions for Correct Use
If a Special I/O read/write error occurs, the most significant bit (word address n, bit 7) of the
Function Code turns ON. Prepare a program that starts error processing from this bit on the
host.
In Modbus communication, the MX2/RX-series inverters set control input, status monitor, or other bit
information as coil information. This means that you cannot set/check data by reading/writing from/to
communications registers.
Use the following registers provided to enable reading/writing of input and output bit information.
Register No. 1F01 hex for CompoNet output (Inverter control input)
Error
Code
Name
Description
01 hex
Function Code Error
A code other than 03/10/43 or 50 hex is set as function code.
02 hex
Register No. Error
The specified Register No. does not exist.
04 hex
Slave Device Error
The Option Board failed to communicate with the inverter.
21 hex
Data Setting Error
An upper or lower limit for the write data setting range is
exceeded.
22 hex
Write Mode Error
Writing to a register that is write-prohibited or in a read-only
state (for example, during operation).
23 hex
Register Size Error
Reading/Writing 2-byte data from/to a 4-byte register or 4-byte
data from/to a 2-byte register.
Reading/Writing Input/Output Bit Data (Modbus Coil Information)
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
–
In8
In7
In6
In5
In4
In3
In2
In1
–
–
RS
EXT
Dir
Opr
–
Value
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Opr
RUN command (0: Stop/1: Run)
In3
General-purpose output terminal [3]
Dir
Rotation direction command
(0: Forward/1: Reverse)
In4
General-purpose output terminal [4]
EXT
External trip
In5
General-purpose output terminal [5]
RS
Reset
In6
General-purpose output terminal [6]
In1
General-purpose output terminal [1]
In7
General-purpose output terminal [7]
In2
General-purpose output terminal [2]
In8
General-purpose output terminal [8]
Содержание 3G3AX-MX2-CRT-E
