background image

5.

Accurately center the media using the supplied ruler. Media should be centered within 1mm on
the ruler.

[44] Ruler to Center Media

NOTE

The supplied ruler has both metric (millimeters) and imperial (inches) scales. When a
media roll is centered on the shaft, and the ruler is placed as shown in the photo, the value
on the ruler scale will match the width of the roll. For example, in the photo a 2 meter (or
2000mm) roll is centered on the media shaft.

6.

Lock the supply media shaft core locks by turning the 5mm hex key clock-wise.

7.

Re-check that the media is still centered as locking the core may cause the roll to shift (usually the
shift is from 1 to 2 millimeters to the right).

Next: Load an Empty Core and Install it in the Take-up Position

8.

Place an empty media shaft on a suitable work surface and unlock the media shaft locks with the
5mm hex key.

9.

Slide an empty media core that is at least as long as the supply media width onto the take-up
shaft.

10.

Roughly center the core and then insert the shaft into the Take-up (top) position on the RMO unit.

NOTE

Make sure that the core lock and coupler end of the shaft are on the right side of the
printer.

11.

Lock the take-up media shaft core locks with the 5mm hex key.

Result

The RMO is now ready to print on the roll media.

Load an Empty Core and Install in the Take-up Position

Procedure

1.

Place the empty take-up media shaft on a suitable work surface and unlock the media shaft locks
with the 5mm hex key.

Load an Empty Core and Install in the Take-up Position

Chapter 6 - How to Operate the Roll Media Option

85

Содержание Arizona 318 GL

































































































































































































































Отзывы: